Release spray Semiperm™ Monofilm, 400 ml

    silicone-free, up to 140 °C

    Release spray Semiperm™ Monofilm, 400 ml

    Universally applicable liquid external release agent, solvent-based and with short drying times.

    • Heat resistant up to 140 °C
    • Solvent-based
    • Multi purpose-product
    • Semi-permanent: multiple releases per application
    • Raise mould temperature to increase slip effect
    • Silicone-free formulation
    • Short drying time
    • Renders time-consuming wax and polishing cycles unnecessary

    The use of this product eliminates the need for repeated time-consuming waxing and polishing, as a single application allows, after some starting time that demands the frequent treatment of the mould, several demouldings.

    Release spray Semiperm™ Monofilm forms a monomolecular film that adheres to the mould and does not show any affinity to the moulded parts.

    Release spray Semiperm™ Monofilm is silicone-free and suited for the purpose of the processing of thermosets like polyester (cold and hot moulding), epoxy and phenolic resins. In particular, when the processing takes place at elevated temperatures (> 50 °C), flawless results are obtained.

    Processing:
    Release spray Semiperm Monofilm should be shaken prior to use.

    The picture shows the importance of homogenizing liquid release agents well before processing:

    1.) Thoroughly stirred or shaken

    2.) After a few days of rest, the active ingredient settles and the solvent separates to the surface. If the two are not thoroughly mixed again before processing, there is a risk that almost only solvent will be applied during application. The separating effect is then correspondingly poor or does not occur at all.

    Prior to the first application of release spray Semiperm™ Monofilm, the moulds have to be cleaned thoroughly from residues of dirt and former release agent. The next step is to apply release spray Semiperm™ Monofilm as an even, thin film and allow it to dry. After a short flash-off time of 1-2 minutes, the mould surface can be polished with a lint-free cotton cloth to a high gloss finish. Repeat this procedure 4-5 times at new moulds. Before starting the production, ensure that the film is absolutely dry.

    Consumption:
    25-30 g/m²

    Please note:
    If used in the processing of prepregs, we highly recommend doing preliminary testing, due to the often high pressure used there is a risk that the release agent is going to be damaged mechanically. Thus, the demoulding can be made difficult or even impossible. The same applies to press-moulded parts (mould and counter mould) when processed with high pressure.

    Important note on substrates:
    This product contains solvents based on hydrocarbons (see under Additional Information --> Safety Data Sheet). It also contains a small amount (< 2 %) of aromatic hydrocarbons. Some surfaces made of plastic (e.g. polycarbonate, Plexiglas®, various varnishes, putties) are dissolved by it so that an impression cannot be taken. It is essential to check this before use, either by referring to resistance lists for the materials or by carrying out a preliminary test.

    For sensitive surfaces, we alternatively recommend PARTALL® Coverall Film PVA from Rexco.

    For more info see (in german, translator included) R&G Wiki

    Release spray Semiperm™ Monofilm, spray can/ 400 ml

    R&G

    Item no.  1651041 66 in stock  (delivery time 1-2 days)

    Add to Shopping List

    18,78 
    (Base Price 46,95 € /  L)

    Scaled Price

    • From Qty 2:  5,0%
    • From Qty 3:  10,0%
    • From Qty 6:  15,0%
    • From Qty 12:  20,0%
    • From Qty 24:  25,0%
    • From Qty 36:  30,0%
    - +

    all Prices  price incl. VAT, possibly plus shipping

    Article information

    type: ga
    language: [language]
    info3: [info3]
    filetype: [filetype]
    url: [url]
    Instructions for use
    type: si
    language: [language]
    info3: [info3]
    filetype: [filetype]
    url: [url]
    MSDS
    type: pi
    language: [language]
    info3: [info3]
    filetype: [filetype]
    url: [url]
    Product information
    type: td
    language: [language]
    info3: [info3]
    filetype: [filetype]
    url: [url]
    type:
    language: [language]
    info3: [info3]
    filetype: [filetype]
    url: [url]

    Hazards identification - Release spray Semiperm™ Monofilm, 400 ml

    Hazard components for labelling

    Naphtha (petroleum), hydrotreated light; Benzene content < 0.1%
    xylene
    Solvent naphtha (petroleum), light arom.; Benzene content < 0.1%
    Naphtha (petroleum), hydrotreated heavy; Benzene content < 0.1%

    Signal word: Danger

    Pictograms:

    GHS02 GHS07 GHS08 GHS09

    Hazard statements

    H222 Extremely flammable aerosol.
    H229 Pressurised container: may burst if heated.
    H304 May be fatal if swallowed and enters airways.
    H315 Causes skin irritation.
    H336 May cause drowsiness or dizziness.
    H373 May cause damage to organs through prolonged or repeated exposure.
    H411 Toxic to aquatic life with long lasting effects.

    Precautionary statements

    P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
    P260 Do not breathe dust / fume / gas / mist / vapours / spray.
    P305 P351 P338 IF IN EYES: Rinse continuously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing.
    P410 P412 Protect from sunlight. Do not expose to temperatures exceeding 50°C / 122°F.
    P501 Dispose of waste according to applicable legislation.