Epoxy Resin MP Advanced + Hardener MP Advanced

    Set of two components:
    1.4 kg, up to 238 °C

    Epoxy Resin MP Advanced + Hardener MP Advanced

    High-temperature, epoxy based laminating resin

    • Two component
    • Heat-distortion temperature: 238 °C (Tg measurement according to DSC)
    • Low mix viscosity

    Pot life (25 °C/500 g): 12 hours

    Mixing ratio:
    100 : 40 parts by weight resin : hardener
    100 : 48 parts by volume resin : hardener

    Gel time (thin coats < 0.5 mm): 18 hours
    Pre-curing: 8 h at 100 °C
    Post-curing schedule: Start at 100°C and heat up with a temperature increase of 10 °C/h to 200 °C, hold it for 12 h
    The cooling rate should not be higher than 50 °C/h.

    Technical data:
    Density (ISO 1183): 1.1 g/cm³
    Hardness (ISO 868): 85 D Shore
    Flexual strength (ISO 178): 88 MPa
    Tensile modulus (ISO 178): 3500 MPa
    Compressive strength (ISO 604): 153 MPa
    Glass transition temperature (Tg): 238 °C (nach DSC)
    Impact strength: 3 kJ/m²

    Applications:
    Moulding materials, which are subjected to extremely high thermal and chemical loadings, such as resonance tubes, deep drawing dies, conduit pipes, containers as well as high temperature applications in the aerospace and electronic industries.
    Suitable for all conventional processing methods such as hand lay-ups, pressure moulding and filament winding.

    Epoxy Resin MP + Hardener MP/ 1,40 kg

    R&G

    1 kg Epoxy Resin MP + 400 g Hardener MP

    Item no.  1251552 Short delivery time

    Add to Shopping List

    166,46 
    (Base Price 118,90 € /  kg)

    Scaled Price

    • From Qty 2:  5,0%
    • From Qty 8:  10,0%
    • From Qty 16:  15,0%
    • From Qty 32:  20,0%
    • From Qty 64:  25,0%
    • From Qty 96:  30,0%
    - +

    all Prices  price incl. VAT, possibly plus shipping

    Article information

    type: ga
    language: [language]
    info3: [info3]
    filetype: [filetype]
    url: [url]
    Instructions for use
    type: si
    language: [language]
    info3: [info3]
    filetype: [filetype]
    url: [url]
    MSDS
    type: pi
    language: [language]
    info3: [info3]
    filetype: [filetype]
    url: [url]
    Product information
    type: td
    language: [language]
    info3: [info3]
    filetype: [filetype]
    url: [url]
    type:
    language: [language]
    info3: [info3]
    filetype: [filetype]
    url: [url]

    Hazards identification - Epoxy Resin MP Advanced + Hardener MP Advanced

    Hazard components for labelling

    Resin

    Tetraglycidyl methylenedianiline
    1,4-Butandiol-diglycidylether

    Hardener

    Diaminoethyltoluol 1,2-Diamino-cyclohexan
    Bisphenol A
    4,4'-Isopropylidendiphenol

    Signal word: Danger

    Pictograms:

    GHS05 GHS07 GHS08 GHS09

    Hazard statements

    H302 Harmful if swallowed.
    H312 Harmful in contact with skin.
    H314 Causes severe skin burns and eye damage.
    H315 Causes skin irritation.
    H317 May cause an allergic skin reaction.
    H318 Causes serious eye damage.
    H319 Causes serious eye irritation.
    H332 Harmful if inhaled.
    H335 May cause respiratory irritation.
    H361f Suspected of damaging fertility.
    H373 May cause damage to organs through prolonged or repeated exposure.
    H400 Very toxic to aquatic life.
    H410 Very toxic to aquatic life with long lasting effects.
    H411 Toxic to aquatic life with long lasting effects.

    Precautionary statements

    P201 Obtain special instructions before use.
    P280 Wear protective gloves / protective clothing / eye protection / face protection.
    P301 P310 IF SWALLOWED: Immediately call a POISON CENTER or doctor.
    P302 P352 P312 IF ON SKIN: Wash with soap and water. Call a POISON CENTER or doctor / physician if you feel unwell.
    P304 P340 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
    P305 P351 P338 IF IN EYES: Rinse continuously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing.

    Special labelling of certain mixtures

    EUH205 Contains epoxy constituents. May produce an allergic reaction.